快將復活 -- 30cm F4 Newtonian

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

快將復活 -- 30cm F4 Newtonian

文章 LT » 週一 05 10月, 2020 19:37

昏睡了十數年,是時候要覺醒......
DIY_mount_RA.jpg
DIY_mount_RA.jpg (448.18 KiB) 已瀏覽 3468 次
最後由 LT 於 週二 28 9月, 2021 23:04 編輯,總共編輯了 24 次。

頭像
Eddy So
夸克星
文章: 16057
註冊時間: 週四 04 12月, 2008 22:35
來自: 中男海

Re: 快將復活

文章 Eddy So » 週一 05 10月, 2020 21:31

[Good Job]

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

Re: 快將復活 -- Start from rebuilding DEC part

文章 LT » 週五 09 4月, 2021 00:40

So as to reduce the total weight of counterweight needed for balancing 12.5" F5 Newtonian, bought an aluminum round bar for machining.
DEC_axle.jpg
DEC_axle.jpg (442.03 KiB) 已瀏覽 3115 次

頭像
Eddy So
夸克星
文章: 16057
註冊時間: 週四 04 12月, 2008 22:35
來自: 中男海

Re: 快將復活 -- Started from rebuilding DEC part

文章 Eddy So » 週五 09 4月, 2021 20:47

[Good Job]

anyone
夸克星
文章: 14338
註冊時間: 週六 07 2月, 2009 12:13
來自: hong kong

Re: 快將復活 -- Started from rebuilding DEC part

文章 anyone » 週六 10 4月, 2021 10:07

[Good Job]

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

Re: 快將復活 -- The most difficult part

文章 LT » 週一 12 4月, 2021 22:08

To thread the DEC shaft, it is the most diffcult part of this project. Because working length to my lathe is just about 15".
DEC_threading.jpg
DEC_threading.jpg (514.33 KiB) 已瀏覽 3030 次

頭像
Wongsir
壇主
文章: 3991
註冊時間: 週六 28 6月, 2003 12:03
聯繫:

Re: 快將復活 -- The most difficult part

文章 Wongsir » 週二 13 4月, 2021 11:38

[Good Job] [Good Job]

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

Re: 快將復活 -- Another difficult part

文章 LT » 週四 15 4月, 2021 19:53

Another difficult part completed today.

So as to install the gear wheel onto the DEC shaft, I have to tailor made an adapter for doing so. Here it is.
DEC_gear.jpg
DEC_gear.jpg (369.96 KiB) 已瀏覽 2969 次
And measurement shows 0.03mm variation peak to peak for one cycle of rotation.
DEC_gear_measure.jpg
DEC_gear_measure.jpg (305.07 KiB) 已瀏覽 2969 次

頭像
Eddy So
夸克星
文章: 16057
註冊時間: 週四 04 12月, 2008 22:35
來自: 中男海

Re: 快將復活 -- Another difficult part

文章 Eddy So » 週四 15 4月, 2021 22:37

[Good Job]

頭像
Wongsir
壇主
文章: 3991
註冊時間: 週六 28 6月, 2003 12:03
聯繫:

Re: 快將復活 -- Another difficult part

文章 Wongsir » 週五 16 4月, 2021 10:42

[Good Job]

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

Re: 快將復活 -- Plate for installing the DEC worm

文章 LT » 週三 21 4月, 2021 23:45

According to my design and measurement, a plate of 6mm thick is necessary for installing the DEC worm, and it was milled from a rectangular aluminum plate.
Plate_DEC-worm.jpg
Plate_DEC-worm.jpg (368.45 KiB) 已瀏覽 2885 次

頭像
Eddy So
夸克星
文章: 16057
註冊時間: 週四 04 12月, 2008 22:35
來自: 中男海

Re: 快將復活 -- Plate for installing the DEC worm

文章 Eddy So » 週四 22 4月, 2021 20:37

[Good Job]

頭像
Wongsir
壇主
文章: 3991
註冊時間: 週六 28 6月, 2003 12:03
聯繫:

Re: 快將復活 -- Plate for installing the DEC worm

文章 Wongsir » 週六 24 4月, 2021 10:18

[Good Job]

LT
夸克星
文章: 2507
註冊時間: 週日 17 8月, 2003 23:20
來自: YL
聯繫:

Re: 快將復活 -- MT-4 goto motor

文章 LT » 週一 26 4月, 2021 00:54

Lack confidence on soldering the wires onto a new DIN socket, and then use a very bad method to detach the socket from the motor housing.
MT-4.jpg
MT-4.jpg (243.47 KiB) 已瀏覽 2753 次

頭像
littleming
夸克星
文章: 3525
註冊時間: 週三 14 11月, 2012 16:23
來自: chaos
聯繫:

Re: 快將復活 -- MT-4 goto motor

文章 littleming » 週一 26 4月, 2021 09:20

[Good Job] [Good Job]

回覆文章

回到「天文話題 Everything about Astronomy」

誰在線上

正在瀏覽這個版面的使用者:沒有註冊會員 和 10 位訪客